In this article we will discuss the common types of foundations in buildings and the types of soil as well.
- 1 A Guide to Soil Types
- 2 Which Type of Foundation Should You Choose?
- 3 How They Work
- 4 Typical Costs for Foundations
A Guide to Soil Types
A good starting point is to call your local authority Building Control department. They should be willing, informally, to give you an idea of the typical soil type in the area you are building, and the sort of foundation that is appropriate.
Soil can be categorised into, sand, clay, silt, peat, chalk and loam – it is based on the dominating size of the particles within a soil.
Initially, the best way to tell which soil type you have is by feeling it. In short, clay soil feels sticky when wet and smears if you rub it between your fingers, while a sandy soil feels gritty and won’t stay together. It’s wise to test the soil from different locations in your garden, as it can vary enormously.
Rocks such as limestone, granite, sandstone, shale and hard solid chalk have a high bearing capacity. The rock may simply need to be stripped back and levelled off to build from.
Rock can be impervious, so topsoil is likely to require drainage as it is not possible to build soakaways to dispose of rainwater or surface water. Off-mains drainage options will also be very limited.
his type of soil can be either light or heavy but always highly alkaline due to the calcium carbonate within its structure.Strip foundations are commonly used in chalk. Providing the chalk is not too soft, widths of 450mm for low-rise buildings are generally acceptable. The depth of the foundation must be below any frost action (700mm). If the chalk is soft it will need to be excavated until firm chalk is reached.
Chalk soils can be prone to erosion so be wary of hollows or caves.
Gravel and sand
Dry compact gravel, or gravel and sand subsoils are usually adequate for strip foundations. Generally a depth of 700mm is acceptable, as long as the ground has adequate bearing capacity.
This type of soil is light, warm, dry and often acidic with a low amount of nutrients. It is often known as a light soil due to its high proportion of sand, and little clay – clay weighs more than sand. Beneficially, it has quick water drainage which makes it easy to work with.
Sand holds together reasonably well when damp, compacted and uniform, but trenches may collapse and so sheet piling is often used to retain the ground in trenches until the concrete is poured.
This type of soil is made of over 25% clay – and, because of the spaces found between clay particles, clay soils hold a high amount of water. Unsurprisingly, this soil will drain slowly and will take longer to warm up in the Summer, combined with drying out and cracking in Summer months.
The first 900-1,200mm layer of clay is subject to movement due to expansion and shrinkage depending on moisture content, so it is generally necessary to excavate foundations to a depth where the moisture content of the clay remains stable. British Standard 8004 recommends a minimum depth of 1m for foundations But if there are, or were, trees nearby, depths of up to 3m may be necessary.
In clay, prior to concreting the foundations, the trench is often protected from heave by lining it with a compressible layer (e.g. Clayboard).
Firm clay over soft clay
A traditional strip foundation is sometimes acceptable but it is important not to overdig as this may increase the stress on the softer clay beneath. A common solution is to dig wide strip foundations with steel reinforcement — however an engineered foundation may be necessary.
Peat and loose waterlogged sand are very poor subsoils. If the peat can be stripped back to find suitable load-bearing ground of at least 1.5m depth, strip foundations may be suitable. A reinforced raft foundation will likely be required.
Where ground has previously been excavated and filled, it is generally necessary to dig down to a level beneath the area of the fill.
Sloping sites require stepped foundations. Guidelines are given in the Building Regulations.
Which Type of Foundation Should You Choose?
A continuous strip of concrete supporting load-bearing walls. For a single storey building strip foundations will typically be 450mm wide and at least 200mm deep, and for two storeys 600mm wide and 200mm deep.
Deep Strip Foundations: Deep strip foundations: Where strip foundations need to be at a lower level to reach soil with suitable bearing capacity, a wider, deeper trench can be dug to work in, and the strip foundations dug and poured at a lower level. Walls are then built up to ground level in masonry.
Wide Strip Foundations: Wide strip foundations: Where the soil is soft or of a low load-bearing capacity, wide strip foundations can be used to spread the load over a larger area, reinforced with steel so that the loading per m² is reduced.
Due to the high cost of labour, deep strip foundations have largely been replaced by trench fill. Trenches are dug to a depth where the subsoil provides sufficient load-bearing capacity, and the whole trench is filled with concrete. Steel reinforcement may be added in areas close to trees.
Compared to deep strip foundations, trench fill minimises the width of the dig and the labour and materials required for building masonry below ground level, offsetting the cost of the additional concrete.
A reinforced concrete raft or mat is used on very weak or expansive soils such as clays or peat. They allow the building to ‘float’ on or in the soil. A raft is used where the soil requires such a large bearing area that wide strip foundations are spread too far, making it more economical to pour one large reinforced concrete slab. A raft is an alternative to piles as it can be less expensive.
Short bore pile and beam: Where the ground conditions will not support strip foundations and the depth of trench fill foundations become uneconomic, or ground conditions make them unsuitable, a series of columns (piles) can be bored and cast in-situ, or precast piles driven into place until they reach stronger strata.
Short bore piles are typically 2–3m long and can be reinforced with steel. Each pile is then connected at the top by a precast horizontal beam of reinforced concrete. A suspended reinforced concrete ground floor can then be built using precast components, or cast in situ.
Friction Piles: A similar concept to short bore pile and beam used in situations where there is no suitable bearing stratum at an acceptable depth. Friction piles rely on skin resistance against the soil.
Used when isolated loads need to be supported, for instance to support the columns of a steel or post and beam frame house. The load is concentrated on a small area.
How They Work
In basic terms, the purpose of a foundation is to distribute the weight to be carried over a sufficient surface as to prevent the subsoil from spreading and avoid an unequal settlement of the structure. This particular example is of a concrete strip foundation. The strip footing must be considerably wider than the wall it supports in order to be structurally sound.
The depth of foundations varies with the character of the subsoil, but any brick wall below ground, such as this wall base, should be built with cement mortar. A drainage membrane prevents the intrusion of water onto the foundation wall. A suspended slab is supported at the wall base over the hardcore. A subsoil drain is laid beneath the ground in gravel to dry out damp soil and lead seepage water away from the foundations to a public drain.
Typical Costs for Foundations